Matt varnish 2K incl. hardener
5 l + 0.5 l
Item no. 1058
Matt varnish 2K is the final step: it seals decorative wall and floor surfaces and dries transparent and silk-matt. The two-component PU sealer is water-based. On dark surfaces, the matt look lightens the shade slightly. The container holds 5 l of base and 0.5 l of hardener, which you mix 10 to 1. Roll the varnish on in at least two coats, at approx. 0.08 to 0.125 l per m² and coat. The second coat goes on within 24 hours; after that, only with intermediate sanding. Substrate and surroundings must not fall below 5 °C during application and drying. At 20 °C and 65 % rel. humidity, the surface can be recoated after approx. 4 hours, walked on for light use after 24 hours and fully loaded after 7 days.
- Water-based, also approved as a top seal for wet rooms on walls and floors
- Load capacity: walkable after 24 hours, full load after 7 days
- Under 30 g VOC per litre
Price after account approval
Materea supplies applicators. With a valid VAT ID your account is approved immediately and you see all prices.
Coverage: approx. 22 m² with two coats, depending on the substrate
Register as a businessAlready approved? Log in
Matt varnish 2K
Price after account approval
Quantity calculator
From the area to the container.
Enter the area, read off the container combination. We calculate with the value from our technical data sheet: 0.125 l per m² and coat, two coats.
The system build-up
Matt varnish 2K is layer five. You need the rest to go with it.
A surface lasts because the layers fit together. Everything here is matched to Matt varnish 2K and comes in one order.
The build-up for this surface
Hardener is also available separately: Extra hardener, 0.5 l.
Technical data & downloads
The figures for application.
All values come from our technical data sheet and the test reports.
Application
Preparation
- Mixing ratio10 : 1 (base to hardener)
- Application temperatureat least 5 °C during application and drying, substrate and surroundings
- Toolsshort-pile varnish roller or nylon roller
- Applicationin at least two coats
Times until the surface can take loads
- Next coatwithin 24 hours, otherwise intermediate sanding with fine grit
- Ready for further workafter approx. 4 hours at 20 °C and 65 % relative humidity
- Walkableafter 24 hours for light-duty use
- Fully loadableafter 7 days of drying and hardening at 20 °C
Values and conditions
- Consumptionapprox. 0.125 l per m² and coat
- Density1.05 g/cm³ at 20 °C
- Solids content30 %
- VOC contentunder 30 g per litre, GISCODE BSW 20
- Usedecorative wall and floor surfaces, including wet rooms on walls and floors
- Storage stabilityat least 12 months, dry and frost-free at 5 to 30 °C
Consumption and time values depend on the substrate and room climate. The technical data sheet is binding.
Downloads
Merkblatt Nr. 301 Technical data sheet- Safety data sheet, basePDF
- Safety data sheet, hardenerPDF
Downloads after log-in. Log in or Register as a business.
Questions
What applicators ask about this.
Frequently asked questions
Base and hardener, in what ratio do I mix them?
10 to 1: 10 parts base to 1 part hardener. The containers are designed for exactly this: 5 l of base in the canister and 0.5 l of hardener in the bottle.
When can I varnish after trowelling?
On T-Razzino+ 2K, no earlier than 12 hours after the second trowel application. Beforehand, lightly sand the dried surface with 80 to 120 grit and remove all dust. For other trowel coatings, follow their own data sheet.
Is one coat of varnish enough?
No, at least two coats. If more than 24 hours pass between the first and second coat, sand lightly with a fine grit before the second application. Allow about 0.08 to 0.125 l per m² per coat.
When can the surface be put under load?
It can take full loads after 7 days at 20 °C. The varnish is dry and can be recoated after around 4 hours at 20 °C and 65 % relative humidity, and it can be walked on for light use after 24 hours. Lower temperatures and higher humidity extend each of these times.
What should I roll with so that no streaks are left?
With a short-pile varnish roller or nylon roller. Pour the varnish into a paint tray, wet the roller well and let it soak in for a few minutes. Roll on generously in a crosswise pattern, spread the varnish evenly in parallel lanes and lay off. Do not leave any puddles.
What the surface still needs.
Primer and sealer are part of the build-up. The times given above apply to the fully sealed surface.
